The epoxy you pour is only half the equation. The other half is the mold.
Choose the wrong mold material and it bonds permanently to your casting -- no amount of pulling will free it. Go too thick in a mold that wasn't built for depth and you're dealing with a cracked, distorted piece and a lot of wasted resin. Epoxy molds matter more than most new casters realize, and getting them right isn't complicated once you understand what you're working with.
This guide covers the most common mold types for epoxy casting -- silicone, melamine, and plastic -- when to use each, how to prep them before you pour, and how to match the right resin to the right depth.
Epoxy resin molds are the forms that shape a casting while the resin cures -- they determine the final geometry of the piece, control whether the resin releases cleanly, and transfer surface texture directly to the finished face. The mold material matters because epoxy bonds aggressively to anything porous or reactive. Silicone, melamine, and low-surface-energy plastics like polyethylene and polypropylene don't bond to cured epoxy, which is why those are the materials to reach for.
The most common epoxy mold materials are silicone, melamine with tuck tape, and low-surface-energy plastics -- each with a different release profile, depth capacity, and surface finish.
Silicone molds are the default for small and mid-size castings: coasters, serving boards, charcuterie boards, jewelry, resin art panels, and small decorative objects. They're flexible, completely self-releasing, and they transfer a smooth, glossy surface to the casting. No release agent required -- you peel the mold away from the cured piece rather than the other way around. They also hold up well to repeat pours; a quality silicone mold can handle dozens of castings before it wears out.
Pre-made silicone molds come in a huge range of shapes and sizes. You can also make a custom silicone mold using pourable room-temperature vulcanizing (RTV) silicone when you need an irregular or one-off shape.
Melamine-coated MDF with tuck tape is the workhorse for river table builds and any large, flat pour. Melamine doesn't bond to epoxy, so the resin releases clean. The tuck tape -- a slick, peel-and-stick HVAC tape -- covers seams, corners, and any raw edge where the resin would otherwise leak or stick. A well-built melamine mold gives you a smooth, flat bottom with predictable geometry.
For a river table, the mold is typically three walls and a base: two long melamine boards for the sides, a melamine sheet for the floor, and end caps. Tuck-tape every seam and check for gaps before you mix a drop of resin.
Low-surface-energy plastics -- polyethylene containers, HDPE bins, polypropylene cups -- don't bond to epoxy. They're useful for medium-size castings like embedded objects, cast panels, and smaller decorative pieces where a container works as the mold itself. Test an unfamiliar plastic before committing to a large pour: drop a small amount of mixed resin in a corner, let it cure, and confirm it releases cleanly.
What to avoid: Raw wood bonds. Cardboard bonds. Most foam melts or distorts from the heat of a curing pour. Glass bonds unless it's waxed and treated. None of these are reliable mold materials without significant preparation.
| Mold Type | Release Agent Needed? | Depth Suitability | Surface Finish | Reuse |
|---|---|---|---|---|
| Silicone (pre-made) | No | Small to medium | Smooth, glossy | High (dozens of pours) |
| Melamine + tuck tape | No (if well-sealed) | Large and deep (up to 4") | Smooth, flat | Medium (rebuild per project) |
| Polyethylene/HDPE | No | Small to medium | Depends on container | Low to medium |
| Raw wood | Seal coat required | Any (once sealed) | Transfers wood texture | Low |
| Waxed glass or metal | Yes (wax + release spray) | Flat pours | Very smooth | Low |
Before pouring any casting resin into a mold, confirm it's self-releasing or apply a mold release agent -- and seal every raw wood surface that touches the resin.
Silicone molds: Typically need no preparation. Wipe them clean and make sure they're completely dry. A light mist of mold release spray before each pour will extend the silicone's service life, but it's not required. Check for any tears or holes -- liquid resin will find them.
Melamine mold builds: The melamine surfaces are ready to go. Your job is sealing the seams. Run tuck tape over every joint where boards meet. The resin will find any gap, and even a small leak on a large pour is a real problem. Pay attention to corners and end caps.
If the live-edge wood slabs inside a river table mold have any exposed channels, checks, or voids, apply a thin brushed-on coat of Table Top Epoxy 1:1 to those surfaces before the Liquid Glass Deep Pour goes in. Let it reach tacky -- not fully cured -- then pour. If it cures fully before you pour, lightly sand with 220-320 grit and wipe with 90%+ isopropyl alcohol to restore the bond surface.
Plastic containers: Clean and dry is all that's needed for polyethylene or HDPE. Don't use a solvent to clean them -- some solvents affect low-surface-energy plastics. A dry cloth or a blast of compressed air handles most situations.
Waxed molds: Apply wax in thin even coats, buff lightly, and let it dry fully before pouring. Heavy or uneven wax can leave a haze on the casting surface where it contacts the mold.
The resin you choose must match the mold's depth -- Liquid Glass Deep Pour handles 2-4 inches in a single pour, the 24 Hour variant handles up to 1 inch per layer, and Table Top 1:1 is a coating product, not a casting resin.
This is the most common setup mistake, and it's worth being direct about: you cannot substitute Table Top Epoxy 1:1 for a deep-pour casting resin. They're different formulations for different jobs. Table Top is designed for thin, high-gloss coatings at up to 1/4 inch. Pour it deep into a mold designed for 4 inches and you'll generate uncontrolled heat, cracking, or a failed cure.
This is the casting resin. Mix 2 parts resin to 1 part activator by volume (100:44 by weight). It's designed for a single pour at depths that would take multiple flood coats with a coating product. Available starting at $49.99 for a 48oz kit, scaling through 3-gallon and bulk kits for larger projects.
Gel time runs 10-12 hours; you can demold at 48-72 hours. Ideal working temperature is 70-84F, but because more volume generates more heat as it cures, stay toward the lower end of that window for deep pours.
Same 2:1 ratio, faster schedule. Good for charcuterie boards, serving trays, small panels, and layered castings where you want a quicker turnaround. Demold at 24-36 hours. Full cure and maximum hardness at 30 days.
The art and craft product. Mix equal parts by volume -- this is a 1:1 ratio, different from the casting resins above. It's the product for petri art, small coasters, tumblers, and jewelry where depth is shallow, working time matters, and clarity is everything. Pigment at or under 12%, no acrylic colorants.
Once the mold is prepped and the resin is chosen, measure exactly, mix completely, and pour slowly -- and don't scrape the bucket into the mold.
Mixing: Measure resin and activator precisely by volume. For Liquid Glass Deep Pour, that's 2 parts resin to 1 part activator. Combine in a clean, dry container and stir for a minimum of 5 minutes, scraping the sides and bottom throughout. Then transfer to a second clean container and stir for 3 more minutes. The double-bucket technique is in the product directions for a reason: unmixed material clings to the walls of the first container, and if it ends up in your mold, it creates soft spots in the finished piece.
Pouring: Pour slowly and steadily from one end of the mold. Let the resin self-level -- it'll find flat on its own. Don't pour from height into a deep mold; keep the pour close to the surface to minimize bubbles from the fall.
After pouring, do not scrape the mixing bucket into the mold. The residue at the bottom and sides may be incompletely mixed. It's a small amount relative to your total pour, and the risk isn't worth it.
Bubbles: Give the resin a couple of minutes to settle, then sweep a heat gun at least 6 inches above the surface, back and forth, until surface bubbles pop. Don't hold the heat gun in one spot -- localized heat causes surface distortions.
Cure time: Let the pour rest undisturbed in a dust-free environment. Liquid Glass Deep Pour gels in 10-12 hours. You can demold at 48-72 hours, but the piece won't be at full hardness until 30 days.
Demold Liquid Glass Deep Pour at 48-72 hours -- it's solid enough to handle without distorting, but maximum hardness is 30 days out.
For silicone molds, start at the edges. Work your fingers under the rim and flex the mold away from the casting gradually. Controlled release preserves surface quality better than a hard pull.
For melamine molds, remove the side boards first -- they'll come away cleanly from the cured epoxy. The bottom panel releases once the sides are off. If you used tuck tape on the bottom, peel it slowly.
Surface texture transfers directly: silicone gives a naturally glossy, mirror-like finish. Melamine gives a smooth, satin-to-semi-matte surface. If you want a high-gloss finish on a melamine pour, plan to sand and polish after demolding. Wood grain, live edges, and embedded objects all read clearly through the crystal-clear cured resin -- that's the whole point.
After demolding, any parting lines, seam marks, or slight irregularities can be wet-sanded through grits and buffed to restore the gloss. The sanding and polishing process follows the same wet-sand progression as any Superclear finish.
Silicone, melamine-coated MDF with tuck tape, and low-surface-energy plastics like polyethylene or HDPE are the most common epoxy mold materials. Silicone is self-releasing and best for small and mid-size castings like coasters, jewelry, and art pieces. Melamine builds are the standard for river tables and large flat pours. Polyethylene bins and containers work well for medium-size castings. Avoid raw wood, cardboard, foam, and glass unless you've sealed or prepped them properly.
Not always. Silicone and melamine are self-releasing -- epoxy won't bond to them without extra prep. Polyethylene and polypropylene also release cleanly from cured epoxy. Where you do need a release agent or a thorough seal coat is raw wood, most foams, glass, and metal. Without it, the resin bonds permanently and the mold won't separate cleanly.
Yes, as long as the mold depth matches the resin's pour capacity -- up to 4 inches per single pour for Liquid Glass Deep Pour 2:1. Check the depth of your silicone mold before buying product. For coasters and shallow silicone shapes under 1 inch, 24 Hour Liquid Glass or Designer Art Resin 1:1 are better fits for the depth and cure speed.
For Liquid Glass Deep Pour, you can demold at 48 to 72 hours. The piece will hold its shape, but it won't be at full hardness. Maximum hardness takes 30 days of cure time -- don't assume the piece is finished when it comes out of the mold. For 24 Hour Liquid Glass, demold at 24-36 hours. For Designer Art Resin, the piece feels well-cured at 24 hours, but the same 30-day full-cure rule applies to all.
Mold selection is where a casting project starts -- not where it ends. For the river table process from slab selection and form-building to the finished pour, see our complete guide to how to make a river table. For depth questions -- how much resin can go in a single layer and what variables affect it -- see how deep can you pour epoxy in one layer. We're adding dedicated posts on mold release agents and on building a melamine mold for an epoxy table -- both are in production.
Liquid Glass Deep Pour is available in 48oz kits starting at $49.99 through 3-gallon and bulk kits. For shallower molds, 24 Hour Liquid Glass and Designer Art Resin are available in pint through 2-gallon sizes. Shop at superepoxysystems.com or call us at 888-849-0588 -- Monday through Friday, 8:30 AM-5:00 PM ET.
!